• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are a variety of reasons the ignition of your car could be locked. The key could be dirty or have a broken wafer inside it. This can be corrected by sliding the key into and out of the cylinder several times.

The pins of the lock cylinder could also be stuck. You can make use of a small tack hammer to lightly tap on the cylinder to loosen the pins.

Check the Battery

If your car is in Park or neutral, but doesn't come on when you insert the key into the ignition, there might be an issue with the shifter switch for the transmission. This can be fixed by moving the shifter upwards or downwards to get the car in gear.

If the car still won't turn, the problem could be due to the neutral safety cable or shifter in the transmission. This can be easily solved by a mechanic, or an auto locksmith ignition replacement locksmith in your area.

It's also possible that the ignition cylinder has worn out. Over time, the ignition as well as the key may wear out, causing them to become difficult to remove or insert. A lubricant, such as silicon lock lubricant can help solve this problem by allowing the wafers to slide into place.

Lint from your pocket and adhesive from the tape that holds packages together can build up on the key, preventing it from sliding into the ignition. Clean the key using a cloth, or a cleaner, such as Triflow to resolve this issue. Also, you can make use of a spare key to determine if the issue is with the key or the ignition.

While the key is in the ignition you can tap it with a an hammer that is small. This can cause a slight vibration, which could be enough to loosen the wafers inside the ignition and allow them to slide in the right position. However, you must be cautious not to scratch the ignition key or cylinder.

If all of the above solutions are unsuccessful, it's time to contact a locksmith automotive mechanic to examine the issue. It could be that the key has been damaged in the ignition, or it could be time to replace the whole thing. If the problem is with the key the locksmith will be able to make a new one for you. If the ignition cylinder is the problem then you'll need to take the car to a repair shop in order for it to be replaced. These issues are generally simple to repair.

Check the Steering Wheel

A locked steering wheel can cause the ignition to stop turning. This can happen if the driver is unable to engage it as they exit or enter the vehicle. It is usually caused by yanking on the wheel and securing themself against it with their hands. It could also happen if an individual in the back seat accidentally engages it as they exit the car ignition key replacement.

This is a simple fix that doesn't require going to the mechanic or locksmith. First, ensure that the gear shift is in neutral or Park. If it isn't, simply push or pull the shifter gently until it changes into one of these positions. It is also essential to press the brake or turn on the handbrake prior to trying to turn the key.

If the wheel isn't locked, a quick check of the steering column will confirm that the key is in contact with the lock cylinder. This is typically indicated by a small "Lock" label on the lower portion of the ignition circle. It is easily removed by gently jiggling it or pulling it down with moderate force. It is essential not to apply too much pressure, as this could cause damage to the key, or damage a wafer inside the lock cylinder.

A spare key can be used to deactivate the lock. This could mean that the key is worn and is no longer able to engage the wafers in the lock cylinder. A professional from Karl Chevrolet Webster City can create a new key in the event that this is the case.

If the new key still isn't engaging, a quick spray of oil that penetrates can assist. Apply a small amount penetrating oil around the ignition and keyhole. Then, jiggle it or tap it lightly to activate it. If this doesn't work you, you might need to seek out a specialist at your local dealership for cars. They will be able to provide you with a new key and replace the ignition cylinder in case of need.

Check the Key

It could be that your key has been damaged if it doesn't engage in the ignition. Try removing any foreign material from the key (lint, adhesive from packing tape, etc). You could also try alcohol on the key or Goo Gone to see if it can help.

It is possible that the lock pins inside aren't working properly when you insert the key. If you have a spare key to test, you can try putting it in the ignition, then gently pulling it out. This should allow you to hear and feel if the internal lock pins move, which they should. If not, you could apply lubrication to the pins using graphite powder. You can purchase graphite in small tubes which can be put into the keyhole. This should help the pins slide into position when you insert the key and prevent them from getting stuck.

It is possible that your key has worn out or damaged and isn't able to connect with the pins within the ignition cylinder. This could cause the cylinder to stop to turn, and prevent you from starting your car ignition lock. If this happens you'll need to take your vehicle to repair ignition lock cylinder or locksmith shop for repair.

If you're able to turn your car on with a spare key, and you have eliminated any problems with the battery or steering wheel it could be that the ignition cylinder is worn out. You can try to loosen the lock cylinder by using the blunt end of a screwdriver, or the handle of the hammer (not the head). A gentle tap on the cylinder will usually free it, allowing you to turn your key and start your car. If this doesn't work, you'll need to have the lock cylinder replaced by a mechanic.

Check the Ignition Socket

The ignition socket is the place where your key can slide in and out when you insert it. It can get clogged up with debris, or just wear and wear and tear. Try spraying some silicon lock lubricant (like WD-40) into the ignition to help things move along.

You can also use a small hammer to gently tap the inside of the cylinder for ignition, in an effort to loosen or reset the pins that could be out of alignment. Be careful not to overdo it or you could cause serious damage to the ignition switch.

Before you attempt this, make sure that the car's gearbox is set to neutral or park. A majority of modern cars have an option to lock the steering wheel when it is not in neutral or in park. This can prevent the ignition key from turning.

If you have tried all of these methods and your key doesn't turn, it is possible that the ignition housing has to be replaced. Different vehicles have different procedures for replacing the ignition cylinder. Therefore, it is important to follow the correct procedure.

This typically involves removing the plastic cover that covers the steering column and the ignition assembly. To remove it, you'll need to first adjust the tilt-wheel to the lowest position and then remove any fasteners that hold it in place.

After the cover has been removed, you'll need to take the old ignition cylinder off the steering column. Then, you'll need to check the new ignition cylinder you purchased with the one that was removed to confirm that they are the same. After this step is completed, the new ignition cylinder is able to be installed in the same way that the old one was removed.

It is possible that even with our best efforts, an ignition may become damaged and need to be replaced. It is suggested that if this happens, you contact a Tempe Locksmith. A locksmith can assist you in choosing the appropriate replacement and install it properly to ensure that your car ignition Lock will be able to start up again.