• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and affordable way to improve the security of your home. The process is not for all. It requires a certain amount of patience and skill.

You must replace the cylinder that is inside the knob's body. The cylinder recognizes the key once it's placed into the lock.

Remove the old window Lock Repairs near me

First, remove the old lock. It's a relatively easy process, but it is important to keep a few things in mind. Make sure the new lock is compatible with your door. This will ensure it is secure and doesn't leave a gap in the deadbolt or latch.

After you have removed the latch plate, look for two screws or bolts on the inside of the casing, which hold the casing and the halves of the lock. Remove them with a screwdriver and then remove the lock from the door. If you have a mortise locking mechanism, there is an anchor screw that connects the handle to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.

It is also recommended to remove the latch and deadbolt plug from the hole in the door jamb. Install the new lock. If you're replacing a mortise, you must measure the distance between your lock case and your door edge to make sure that the new lock will fit.

You may want to replace your lock for various reasons, including if you suspect that someone else holds the key or if you have new roommates. You can save money by deciding to remove the lock yourself instead of paying an expert. It's much simpler than most people imagine and can be completed in a matter of a few minutes.

Remove the trim and handle from your door. Then, pry the trim off with a flat screwdriver. You will be able twist off the majority of it and in some cases the handles may fall off completely. The next step is to look for a hole on the inside of the handle and insert a straightened clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Then, look for a small tab on the interior of the lock and press it with a flat screwdriver. After the spindle is removed, you are able to remove the housing and cylinder.

Selecting a new lock

When it comes to choosing a new lock, you have many choices. Look at different types of locks and select one that fits your door's style. Think about the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole along the edge of the door frame). Also, make sure to choose a lock that will accommodate the door's thickness as well as swing.

The majority of door locks have been assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they stand up to use and how difficult to pick or disable. A lock of grade 3 could be the ideal choice for a tranquil apartment in a rural area, whereas a lock of grade 1 may be better suited to the busy streets near a storefront.

Most smart door window locks repair near me require a digital code to open. If you are worried about hacking, or any other security issues, talk to a professional locksmith.

Replacing the cylinder

It is easy to replace damaged or broken doors lock cylinder using a simple DIY project. It is important to select the appropriate cylinder and follow all instructions. First, remove the knob or handle, if it is present. Then with a screwdriver unscrew the trim that surrounds the lock cylinder. Once the trim has been removed, you can access the screws that hold the cylinder in place and remove them with the flat-head screwdriver. The cylinder is then gently pulled from the door.

Be sure to measure the length of your new cylinder before installing it. Measure the distance from the center to the left and right sides of the cylinder with a tape measure. Then, purchase an additional cylinder using the same measurements. This will stop the cylinder from snapping, which could happen when the door is kicked in or when the key is stuck inside.

Place the replacement cylinder inside the door, and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is usually located on the outside of the lock. After that, you can loosen the set screw that should be just a few turns inside the head. It is also necessary to loosen the screw at the edge of the door that fastens the case, if there is one.

After you have removed the lock cylinder after which you can replace it with a new window lock repair by slipping the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder with the stem of the repair upvc window lock indicator, which you can do by removing three tabs on the back of the cylinder using needle-nose pliers. Then, you can attach the second bracket to the back of the cylinder. Then, you need to reinstall the strike plate and latch plate, as well as the retaining ring connected to the top lock cylinder.

Installing the new lock

If you're replacing a previous lock, start by measuring the width of your door. Most residential locksets have a thickness of 1 3/8 to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This will require longer screws as well as a longer spindle extension or tail piece for door knobs.

The majority of locks come with a detailed instruction booklet to help you install the new hardware. Be sure to read the instructions thoroughly prior to beginning the process to make sure that you've followed all of the necessary steps. The booklet will give you an idea of the amount of skill that is required to complete the task. If you're changing a lock for the first time, you may consider asking a more experienced friend for assistance.

It's a good idea to seal the openings of the old lock before installing the new lock. This will stop screws from slipping through the holes, and protect any tiles you may have installed. It also shields your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of masking or gaffer tape. However, you can make use of any tape you have.

After you have removed the screws that connect the interior half of the lock section to the outside side, pull it straight away. It is important to do this as quickly as possible to avoid the lock from accidentally closing on itself and damage the mechanism.

Install the new latch bolt in the upper cross bore of your new lock if it has one. Make sure you place it in the right position, which is usually indicated by an arrow on the faceplate. Then, slide the latch plate on top of the bolt and secure it in place.

Screw the deadbolt to the jamb of the door. Test the deadbolt by throwing it a several times to make sure that it is extended all the way into the strike plate and is completely secure. If you're using an electronic smart lock, make sure to follow the included instructions for programming it. This involves downloading an application, registering your e-mail address, verifying your identity and connecting to the wireless network in order to connect your device.