• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a loose door repair upvc window hinge is a simple task for the majority of homeowners. If the holes for screws have been stripped and will not hold screws, you might need to use dowels and wood glue in order to reinstall the hinge.

Before you do this, however you should clean off any the surface corrosion. This will help the dowels stay in place and give them a solid base to rest on.

Removal of the Hinges

Many hinges for doors can be removed, making it easier to move doors from one side of the frame to the other or take the entire door off if necessary. The removal of the hinges is easy for anyone with a little patience, though you do have to know how to do it right.

If the hinges are painted, you will need to remove the paint before attempting to remove the pins. You may scratch your door if don't take off the paint. Place the hinges in an stainless steel pot and fill it with water until the hinges are submerged. Allow the hinges to sit in the pan for about 30 minutes. The heat from the water should soften the paint and make it easier to remove the pins.

Once the pins have been removed, take the hinges and frame from the door. You can make use of a screwdriver to get the job done, however it is recommended that you make use of a magnetic screwdriver for this task. This type of screwdriver is specifically designed to take out metal screws and aid you in getting the job done much faster.

It is a good idea to spray some lubricant on the hinges prior to trying to remove them. A simple lubricant can help you to move the process along faster and remove the pins and screws more easily. You can find this type of lubricant at a variety of hardware and home improvement stores.

The number of hinges needed will also depend on the type of door you have, and how it is set up. Heavier doors and solid-core doors will need more hinges, while hollow-core doors with a lighter weight may only require two or three.

It is also important to understand the different types of hinges to determine which ones be the most effective for your particular situation. The hinges on the exterior are designed to withstand the weight of a door, whereas hinges for interior use must be able support lighter loads.

Reattaching the Hinges

Sometimes, the hinges on doors get looser and eventually begin to hang out of alignment or sag. This can be a problem, but it's usually easy to fix window hinge. Most of the time an easy tightening of the screw will solve the problem. However, if the screw holes have been stripped out, it can be more difficult to accomplish. A wood dowel could be used to tighten the holes once more.

Begin by drilling out the old hole using a drill bit that is close to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. The dowel should be cut to a length that is the same as the screw to ensure a tight fit. Install the screw again, and tighten to desired level of tightness. If the door has the tendency to be bowed, then add another dowel to the gap and repeat the procedure. Be sure to shut the door slowly so that you can examine the clearances around the perimeter after each adjustment.

Another option is to just make use of the wood plug instead of dowel. This will work as well however it may take some time to set up. You can use a piece of wood that has been whittled down to the proper size. If you don't have a woodworking tool, you can also try using toothpicks or wooden matches as well.

Use a countersink to make the hole smaller for the head of the screw after you have reinstalled it. This will prevent the screw from hitting the edge of the doors as they are closed and opened. This will aid in tightening the screw prior to installing the hinge.

After installing the hinge again, you should apply lubrication to the hinge using a dry lubricant. This will help to prevent it from becoming stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. Apply a thin layer and allow it to penetrate the hinge barrel for around 15 minutes.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you can do a few simple repairs. Make sure the screws that attach the hinge plate to both the door frame and the frame are in good condition. If they are loose, tighten them by using a drill or screwdriver. Be cautious not to over tighten the screws, as this could create gaps at the trim joints or worse, strip out the threads.

If the issue is that the hinge plates are splitting and you want to reattach the plates by putting wood glue to the back of them and then inserting toothpicks or wooden dowels into the holes. The toothpicks and dowels provide a solid base for the screws, which will stop the plates from shifting when you push them in. Allow the glue to dry before attaching the hinge.

Another reason for hinges that are loose is that the screws are stripped or are missing. It is possible to fix this issue by replacing the screws with larger ones. Use a drill that is similar to the size of the screw hole to avoid drilling into the jamb or hinge.

Close the door once you've reattached your hinge and examine the gap between the frame and the door. It should be around the thickness of one nickel all around, or less if there's an existing gap that was caused by a previous door that was not properly hang. This should not be a problem as long as the hinges are installed correctly.

If you find that the hinges remain loose, you can try adding a thicker hinge shim between the hinge plate and the mounting surface to add a little extra space. You can also take off the hinge pin, then pound it down with a heavy hammer to tighten it, or install the hinge of a different type. You can also lubricate your hinges with mineral or jojoba oil to reduce window friction hinges and aid in holding their position. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky, and will also extend their life.

Cleaning the Hinges

The continuous movement of hinges creates friction hinges for Timber windows, which draws dust particles. Without regular cleaning and lubrication, these particles become stuck in the moving parts of a hinge for doors and build up over time. The hinge will get stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication, and inspections will ensure the integrity and functionality of hinges on a door.

Check the hinges to see how much rust has built up on their surface. If the rust has corroded to the point of damaging the surface of the barrel or screw holes, you will require replacement of the hinges. If you are able to save the hinges, begin by brushing away loose rust using steel wool and a wire brush. Then, apply an industrial rust remover or a homemade solution, such as lemon juice to the hinge. Allow the rust-removing solution to remain on the hinges for several minutes in order to penetrate and dissolve any remaining rust.

The tightening of screws can restore hinge functionality if you don't want to spend money or time to replace hinges. If you have stripped the screws however, it might be necessary to add a wooden dowel or shim to the hinge. Dowels made of wood are available in round rods of various sizes and lengths. You can find them at home improvement stores or woodworking supply shops, or online.

A shim may also be made from plastic window hinges or metal, depending on the kind of double glazed window hinge repair you have. To make a dowel, cut a dowel from wood to the desired length. You can dip the dowel into the adhesive of a carpenter and then insert it into the hole. The glue will hold the dowel firmly in the position.

Before you begin cleaning the hinges, lay down a towel or a paper towel to protect flooring and other surfaces from drips and spills that could happen. After you have protected the area clean the hinges with an easy sponge or cloth coated with mild cleaner to get rid of dirt and grime. You can also remove tarnish, dirt, and grime. A small brush or toothbrush can be used to access difficult-to-reach spots in crevices or difficult places.