• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fitting a cat flap can seem intimidating however it's actually quite simple with the proper instructions. Firstly, determine how high you would like the flap to be (on average, belly height). Mark this point on your door and then use the included template as a guide when drilling.

If you have a kitten, or a young kitten you can prop the door open a bit and gradually allow it to enter. Reward it as it passes through.

Take a measurement of the door

A cat flap is a wonderful way to let your pet move into and out of your home whenever it pleases. This can help keep your cat healthy by making sure that it is getting exercise and also being able to go back inside if stuck outside in bad weather, especially during the winter. It can also reduce the amount of time you'll have to allow it in or out and can ensure your home is secure by letting you know when it's been out.

However, it is essential that the flap for your cat is properly fitted to stop your pet from being able to escape through it or be pushed through by other animals (e.g. dogs). It is crucial to determine the height of your pet's belly as well as the doorway of your house in order to ensure that the flap is at the right height. You can adjust the height of your flap when your cat flap cost is smaller or taller than the average.

The next step is to utilize a spirit level mark the center of the door, where you will put the flap. Then, using the marks as an indication, cut out the contour of the flap using the help of a Jigsaw. After you have cut the area then sand the edges to create smooth surfaces. Make any holes that are required.

The process of fitting a cat flap is not as complicated as you think and it should not take more than two hours to finish the entire process from beginning to finish. The process can be slightly more difficult if you have to install it on the form of a uPVC door or composite one. This is because composite doors come in various thicknesses, which can impact the way the holes are cut. This is why we always recommend calling an expert to do the work, particularly in the event that you've never worked with glass before.

Measure Your Cat

A cat flap can save you from listening to your pet's meow for you to let it out or in. This is especially helpful if you are at working all day and your cat is in the house waiting for you to get home in all weathers.

It is crucial to measure your cat's measurements first before you attempt the installation. It might seem like a straightforward task, but it is crucial to get the measurements right. If not, your cat might find it difficult to use.

First, make sure that your cat is calm before taking measurements. You'll need to put your cat in a place where they cannot move. Also, make sure that the measuring tape is straight and not bent against their body. Holding the ruler or measuring tape against their body from the top of their head to the bottom of their tail can allow you to determine an accurate measurement.

Once you've got the measurement of your cat, it is time to look at the door and decide on where to put the flap. It is advisable to position the flap on the highest point of your cat's stomach as this will allow them to move through it without much effort. This will also prevent the flap from making a lot noise as it swings back and back.

You should also think about the thickness and the structure of the uPVC door or composite. While all timber doors have the same thickness to them, uPVC or composite doors can differ greatly in their overall design. This makes fitting the flap for your cat more difficult, as you have to make sure that the hole is the right size.

You can also use the template included in the instructions to mark the location of the hole in the door. This will enable you to determine where the hole must be located and make sure that the template is positioned correctly on the door. It is also helpful to employ a spirit-level to ensure that the template is placed in a straight line against the door.

Cut the Flap

Before you can install your cat flap you need to cut the door panel to create a space large enough for it. This can be a challenging job, and it is recommended to seek the help of an expert cat flap fitter for this job should you not have the skills or experience to complete the task yourself. You can also read the instructions that come in the kit to find out how to do it properly.

To do this, you will need to measure the height of your cat's or kitten's belly and use this as an indication point. A good guideline is to place the flap of your cat about 10 centimeters off the ground, as this is approximately the average height of the cat's belly. This way, your cat will be able to move through the flap without difficulty and also give the other cats or neighbours who are snooping difficult time trying to get in or out.

Once you have determined where the cat flap should be located, mark the position on the door with a pencil. Then, if your kit comes with a template for paper, place this over the door and use the marks to drill holes in every corner of the template. Then, you should be able to cut out the shape of the template and replace it with your cat flap.

You can put in your cat flap cover for winter flap yourself in the door made of wood or uPVC if you are confident using a jigsaw. Make sure you don't cut into any of the door mullions or vertical rails. You can use a Jigsaw to cut your panel into a square or circle depending on the way you'd like it. Be patient, and don't try to force the jigsaw to cut faster.

After the hole has been cut, carefully fit the cat flap into its new home and ensure that it is securely secured. If it has screw caps, then push these onto the protruding screws. After the screws are installed smooth the edges and apply sealant to any gaps. This will prevent draughts from entering your home.

Place the Flap

If you have a simple cat flap, you can open it and encourage your pet to walk through by putting a little bit of cat food in front of the door. You can also try pushing the cat using sticks or your hand. Once your pet is used to walking through the flap it is likely to be able in and out as it wants and you should be able to let it out or in without having to be there holding the door open to allow it in all day (and possibly in all weather conditions).

It is possible to fit a cat flap into the UPVC or glass doors although this may not be quite as straightforward as fitting one into a timber external door since the UPVC doors and some glass doors don't have the same thickness. This can have a major impact on the way you cut out the flap's hole and whether the flap fits correctly after installation.

The mounting kit could include a template showing you the best places to drill holes. If the kit does not include an example you can use a photocopier to create your own. When cutting, it is important to keep the jigsaw from being pushed too hard so that you don't make a larger hole than you need in your door.

The majority of cat flaps are square or rectangular in shape but there are also some which are circular, and they are typically more difficult to place. If you have a circular flap, make sure the hole is located in the right place on your door. In the event that it is not, the cat might not be able to use it, and may be outside all day (or night).

Certain models of cat flaps have locks which let you control when your cat comes in and goes. These are very helpful in the event that you are worried about your cat going out at night and then coming back in the darkness, or if you're at work all day. The lock can be turned on to allow or deny entry, and some can be locked in either direction permitting you to close the door completely. This is particularly beneficial for cats with a chronic illness or older age who aren't keen on going out in rainy weather.