• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your cat leave and come back at their own pace, without needing to let them in or out. They also help stop your cat from urinating inside the house.

It is easier to install a cat flap on a Upvc panel than on a glass one but you'll need some skills and the appropriate tools.

Measure the Door

The installation of a cat flap in a front door can be difficult however, so long as the cat flap is the appropriate one and you follow the directions it shouldn't be too difficult. We will show you how to draw the shape using a jigsaw in order to cut out the door area. Then we will finish the job by attaching the flap. This will ensure the flap remains in place and shields the doors from the damage caused by wind and rain.

To determine the size of the cat flap you require, measure the width of your pet. This will ensure that the flap is big enough to allow your pet to enter and leave the house without needing to open and close the door each time, but also small enough to prevent them from going too far either way.

Once you have the measurements, you can determine the location on the door where the template should be positioned, usually this is done with an X, however some kits come with an illustration that outlines where to drill. If you have one, then attach it to the door and use a pencil to draw around the door. If your door has sill or moulding on the bottom edge then make sure you have clearance from these to keep your cat safe and will prevent them from getting access to your home.

Use a set square to ensure that you're cutting correctly and to ensure the hole is a good rectangle shape. When you are satisfied with the result, you can begin to remove the rest of the door material. If you own a set square then use it to ensure that you are cutting correctly and also to ensure that the hole is a proper rectangle. Once you are satisfied with this you can start to remove the remaining door material.

Draw a Line

The cat flap is a great way to allow your pet to go in and out without worrying about them being in the house with guests or leaving unwanted gifts in the home. It also stops draughts and helps to keep your home's temperature in check. Fitting a cat flap in upvc door panel (relevant webpage) flap to your door may seem daunting to those who haven't done it before. Many people will call an expert carpenter or joiner to complete the work. This is an option but you can do it yourself if the tools are in order and the directions are followed.

It is much easier to do on a wooden door, cat flap in Upvc Door panel but it is still possible using upvc door panel with cat flap fitted. However, you must be careful not to harm the doors because this will invalidate your guarantee. The first step is to take measurements of the door to ensure that it can accommodate the new cat-flap. If you have an ordinary uPVC panel it should be a breeze. However when your door is composite or a different type of door, you might have to be more cautious.

The next step is to determine the height of your cat's stomach. This is the distance between the floor and the bottom of your cat's stomach. You'll need to find an area on the door that will allow your pet to comfortably pass through. Once you've figured out the measurements, you'll be required to mark the space using a spirit level and a pencil so that you are sure that the hole will be suitable for your cat.

After you've marked the area, you're now ready to cut the hole. You will need a jigsaw and it is crucial to take your time to ensure that the cuts are smooth and clean, rather than uneven and rough, since this could damage your door. Wear safety glasses and a dust mask when working with the Jigsaw. Inhaling sawdust is hazardous for your health. After you've completed the cutting process, you will have to smooth out the edges of the hole with sandpaper, so that your cat flap can be fitted easily in place.

Cut a Hole

It isn't easy to fit a cat flap into a door panel or sealed double glazing unit. If you are not very proficient in DIY, it's best to hire an expert to do the work for you. A botched job could not only be ugly and unattractive, but could also be security risks. It could allow cold air to enter when the cat is outdoors and hot air out when the cat is inside.

Mark the hole's position on the door with an eraser and a spirit level. This will ensure it is properly positioned and runs flush with the rest of the door. It is important to have some sandpaper on ready to smooth any edges.

Wear the safety equipment you'll need to use the power tool. If you're worried about the noise, you can get an electric jigsaw that is quieter and easier.

You should only remove the material needed to make the cat flap. A little bit of extra material will be needed to cover the thickness of the wall of the flap, but cutting off more than this can cause problems or harm the frame of the door.

A door made of upvc could contain a metal frame or panel within it that will interfere with the microchip cat flap, and if this is the case, you'll need to cut an over-sized hole to ensure that the metal doesn't get in contact with the wall of the cat flap, if this is the case, it is essential to fill in the gap and make it watertight.

If you're planning to install an animal flap to the frame of a double glazed windows with a metal frame then you'll need to speak to a professional who can provide you with a new glass pane that already has the hole for the cat flap in it. This is less expensive than trying to fit a cat flap in an existing pane of glass that was not made specifically for this purpose.

Place the Flap

Cat flaps allow your pet the freedom to go and come anytime they want, cat Flap In Upvc door panel allowing them to relax at home whenever they want to. If you have an uPVC front door, it may be difficult to install a cat flap. This is especially true if you do not own an glass panel that is cut. If you're able to buy and install a replacement half-glazed uPVC panel then it is possible to install the cat flap to these doors. It's not as easy as simply making a hole in the door however, and there are a few things you'll need to do first to make sure it's safe.

A composite door panel usually has an flimsy plastic outer layer bonded to a soft polystyrene core that is insulating. The material is extremely fragile and care must be taken when cutting into it to avoid causing damage. This kind door comes with a template that you can use to make the hole.

Once you've marked the hole in your front door, it is time to put in the cat flap. You can pick from a wide range of designs, from simple push-button flaps to ones that are microchip-activated and only let your pet in. However, regardless of what type of cat flap you choose it's crucial to ensure that your cat can use the flap without becoming trapped outside in bad weather.

A circular fitting cat flap in upvc door panel is more effective than a square because circles can be cut more securely into the glass. It's because square holes are more likely to crack the glass when they're drilled. This is also a safer option since you don't have to drill into the toughened glass which could break and hurt your pet or your family members. This is particularly important if there are children or elderly people at home who could be injured by glass shards.