• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair French Doors

French doors are an elegant addition to any home they connect outdoor and indoor spaces. However, they can experience problems over time that require prompt attention for both safety and functionality.

Sagging, misalignment and warping of door frame and sash are all common issues. Fortunately, many of these issues can be easily solved with a little time and effort.

Locks that are not aligned

Sometimes doors become stuck or misaligned due humidity, swelling of the wood, or the house settling. This can cause the lock bolt to become loose and making it more difficult to open or close the door. This puts additional strain on the lock, which can eventually result in mangled inner-lock components or even broken locks completely. Fortunately, this is an issue that is quite common and can often be solved with simple DIY methods.

In certain situations all that is needed is a bit of lubrication to allow the door to open and close smoothly. You can apply graphite lubricant, but make sure it is safe for the door. Make sure you clean the area with a moist cloth to clean any debris around the door prior to applying the grease.

A door that hangs off-center can be repaired by loosening and adjusting the hinges until they are aligned with the frame. You must be careful not to over-tighten the screws as this could cause damage to the hinges or damage the door.

If your exterior French door isn't closing properly it could be a sign that there is a blockage in the lock mechanism. This is usually caused by short screws that came from the factory that have come loose over time. Replace the screws with longer ones to remove more wood from the door frames.

You can also adjust the lock, but it's more complex and difficult. Start by loosening either the lock knob or handle with flathead screw. Then, you can remove the lock assembly from its cubbyhole by unscrewing and taking it out. Inspect it for any obstructions before you put it back together and tighten the screw connections.

If the latch doesn't touch the strike plate, you might need to move the strike plate or expand it. If the strike plate is smaller or higher than the latch hole it could hinder the lock from closing and require the assistance of a locksmith. If the hole is too small, you can enlarge it with a metal file or drill.

Sagging

If your doors are sliding or have gaps between them, it can affect the insulating properties of your home and reduce the efficiency of its energy use. These gaps can also block views and cause drafts. There are simple solutions to these problems.

Start by tightening your hinges and aligning them properly. This should take 10 minutes or less, and will not require any tools. If this does nothing to solve the issue, you will need to replace the hinges. They are likely to be at the end of their lifecycle.

Over time, your French doors may become loose due to the weight. To prevent this from happening ensure that the hinges are secured your door and ensure they are secure. It is also recommended to regularly lubricate your hinges with a lubricating spritz to prolong their life.

Replace damaged or old hinges to stop a door from sagging. A new doorknob or freshly painted doors, can affect the position of your French doors.

Other causes of sagging are foundation settlement, wear on the hinges or the wrong changes made to your doors. You can fix a sagging door by tightening or adjusting the hinges.

Also, it is important to check the weather stripping on your doors and to make sure that they're working properly. If they're not functioning then you can remove them and replace them.

Lastly, you should occasionally examine the wood on the door frame for Repair French Doors indications of rotting or warping. These issues can lead to drafts that decrease the effectiveness of your door. They could also cause water leakage or damages to your home.

If your doors are creaking and you have tried the two methods above It is likely that you'll have to remove the door jamb using a hand plane, advises Popular Mechanics. To do this, remove your doors from the hinges. Place them flat on something sturdy like a sawhorse. Mark the places that need planning, and then use a hand plane to smooth these areas of the doorjamb.

Leaks

The vast areas of replacement glass panels for french doors on french door window repair doors make them an ideal source for water leaks, particularly in an area that experiences heavy rainfall. Left untreated the leaks could lead to the frame of the door to rot and the surrounding structure. It is relatively easy to fix these leaks, and it should only take you a few minutes.

Leaks can be caused by a variety of causes, including

A broken seal

Replace the rubber seals on either side of your threshold with new seals. This will ensure that there is a tight fit, and will also stop rainwater from getting inside your home.

Water is leaking through the sill

This issue can be caused in a number of ways such as the absence of a sillpan, or using a metal sill which isn't watertight. If you find that water is gathering around your French door, call the builder and ask them to install sill pans or replace the steel sill with the wooden sill which will resist water.

Obstructions

A leaky seal could cause fog to build up between the double panes of glass on French doors, which block the view and decreases their energy efficiency levels. The issue can be fixed by replacing the old seal with a fresher one that blocks moisture and air.

Loose Handles

A handle that isn't tight could be dangerous since it could fall when you're opening or closing your French door. This issue can be solved by tightening the screws or replacing the handle if it is damaged or worn.

A track stop that's not properly set can stop the doors from sliding correctly which can cause scratches and jams on frames. This issue can be fixed by applying silicone caulk to tracks or track stops. It is also recommended to regularly inspect the exterior surfaces of frames and doors for wear or cracks to ensure they are in good condition.

Warping

If you are not careful, your French doors could start warping because of exposure to heat or moisture. It's worth calling in an experienced handyman with experience fixing a French door. They'll be able to provide advice on the best method to repair french doors your doors and make sure that they are safe to open and close.

If your doors are severely bent, it may be necessary to replace them. If they are only slightly warped, you may be in a position to straighten them by placing damp towels over the affected area. Leave the towels on the door for a few days or even longer until they are completely flattened.

This technique is typically used on uPVC doors, but it could also be applied to wooden doors - provided the wood is well seasoned. The process is difficult and time-consuming, especially if your doors are warped.

The doors could warp if they have been stored improperly. They should be kept clear from building works that generate lots of humidity, such as decorating or plastering work. They should be kept in a flat place on a firm surface.

A damaged strike plate could also cause warping. To remedy this, you need to take the doors off and set them up on the sawhorses. The excess wood can be removed from the bottom and top edges of each door with a hand plane. It is essential to work in small pieces to avoid taking too much off the doors, which could make them too thin and fragile.

After the doors have been rehung, you can screw the strike plate back in place. If the lock does not work the barrel catch might be getting caught on the side of the frame. This is fixable by spraying silicone on the latch. If this isn't working, you might have to replace the latch.