• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fitting a cat flap can appear daunting, but it is fairly simple to install with the right instructions. Firstly, determine how high you want the flap to be (on average or belly height). Note this on the door and use the template included as a guideline to drill.

If you have a young kitten hold the door slightly open and gradually allow it to go through. Reward it when it goes through.

Take a measurement of the door

A cat flap cost near me flap allows your pet to move into and out of your home at any time. This can help with keeping your cat in good health by ensuring that it gets exercise as well as being able to go back in if it is trapped outside in bad weather, particularly during the winter. This will cut down on the time you allow your cat in or out and also make your home safe by notifying you when it's left.

It is crucial to make sure that the cat flap is placed properly to stop your pet from being forced through it or escaping by other animals (e.g. dogs). It is essential to measure the height of your pet's belly as well as the entrance to your home to make sure that the flap is at the correct height. If your cat is larger or shorter than the normal, you can adjust the flap's height by moving it upwards or downwards by a small amount.

The next step is to utilize a spirit level mark the centre of the door that you will install the flap. With the markings as a guide, take an jigsaw to cut the form of the flap within the door. Once you've cut the space, sand down the edges of the door to smooth the surfaces. Then drill any fixing holes required.

Fitting a cat flap should not take longer than two hours. The process is a bit more complicated if you are required to put it in the case of a uPVC door or a composite one. This is due to the fact that these doors are available in a variety of thicknesses, which could affect the way the holes are cut. We always suggest that you call an expert when this is your first time working with glass.

Measure Your Cat

You can save yourself hours of listening to the cat's meows to be let in or out. This is especially helpful when your cat is inside during the winter months when you are at work.

If you want to fit a cat flap on your door, it is essential that you measure your cat before attempting the task. It may seem like a simple task, but it is crucial to get the measurements right. Otherwise, your pet might find it difficult to use.

First, ensure that your cat is calm and not anxious prior to taking the measurements. You'll need to put your cat in a position where they cannot move. Also, ensure that the measuring tape is straight and not bent against their body. Holding the measuring tape or ruler against their body from the top of their head to the base of their tail will allow you to get an precise measurement.

Once you have your cat's measurements then you can examine the door to determine where to put the flap. The best option is to position the flap at the height of your cat's stomach as it will allow them to pass through it without too much effort. This will also stop the flap from making a lot of noise when it swings back and forth.

You must think about the thickness of the upvc door panels with cat flap or composite door too. While timber doors are all of the same thickness, uPVC and composite doors are different in their overall structure, which can make fitting a cat flap more difficult as you will need to make sure the hole you cut is the correct size for your pet.

It is also worth studying the instructions that come with the kit to find an outline of the template that can be used to determine the location of the hole in the door. This will help you determine the location where the opening should be and make sure the template is correctly positioned on the door. Utilizing a spirit level to make sure that the template is sitting flush against the door will also be very helpful.

Cut the Flap

Before you can install your cat flap, you'll have to cut the door's panel to make a space big enough for it. This can be a daunting job so it's recommended you engage a professional to assist you if you don't have the expertise or experience. You can also read the instructions provided in the kit to find out how to do it properly.

You can consider the height of your cat's or kitten's stomach as a reference. In general you should place the flap approximately 10-15 centimeters above the ground. This is the standard height of the belly for cats. This will allow your cat to pass through the flap with ease and will make it difficult for other cats or naughty neighbours to get inside or out.

Mark the position of the cat flap on the door using pencil. If your kit has an outline you can place it on the door. Use the marks on the template to drill holes at each corner. You should then be able to cut the template's shape and replace it with your cat flap.

You can put in your cat flap yourself inside an uPVC or wood door if you are confident using the use of a jigsaw. Be careful not to cut into the mullions or rails that run vertically of your door. You can use a jigsaw to cut the panel into a square or circle depending on the design of your cat flap. Be patient, and don't force the jigsaw into cutting faster.

Once the hole is made and the flap is firmly positioned, carefully place the cat flap into its new location and make sure that it is securely secured. If it has screw caps, then push these caps onto the protruding screws. Once the screws are in place, sand the rough edges of the cut and then seal any gaps to ensure that there aren't any draughts entering into your home.

Place the Flap

If you have an ordinary cat flap, you can encourage your pet to go through it by placing a small amount cat food on the top of the door. Alternatively you can try pushing the cat through using your hands or a stick. Once your cat is used to moving through the flap, it will be able to come and go as it pleases. This will allow you to let it in and out at any time it's wanted.

It is possible to install the flap inside an UPVC door or glass door, however it might not be as simple as installing one inside a wooden exterior door. This is due to the fact that the doors made of upvc door panel with cat flap and some kinds of glass doors don't have an even thickness. This can have a dramatic effect on the way you cut the hole for the flap and will also affect whether the flap will fit properly once it's been put in place.

Depending on the type of cat flap you choose, it may include a mounting kit and a template that will show precisely where to drill holes for it. If the kit doesn't include the template you can use a photocopier to create your own. When cutting, it's crucial to not push the jigsaw to the point that you make a larger hole than you need in your door.

Some cat flaps come in circular designs, which are more difficult to put in. If you have a circular flap, it's important to make sure the hole is in the correct position on your door because if it's not, your cat won't be able to use it and could be left outside all day (or even night).

Some models of cat flap come with locks that let you control when your cat comes in and goes. They are helpful if your pet is afraid of leaving in the dark, Fitting a cat flap or coming back in the dark. They are also useful if you work all day. The lock can be engaged to allow entry or exit, and some can be locked in both directions, permitting you to close the door completely. This is especially helpful for older or ill cats who aren't willing to go out in the rain.