• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

The first line of defense is your door lock replacement upvc door. It will stop unauthorized access to your home. Signs of wear and tear and even instances such as moving into a new house or burglaries, may trigger the necessity of replacing upvc door lock your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to purchase the correct-sized lock.

Deadbolt

If you want to ensure your door is secure from intruders, it's a good idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe, it makes it harder for an intruder to break through the door. A single cylinder deadbolt can be activated by keys on the exterior side and a thumb turn piece on the inside. A deadbolt will only work if it is installed correctly.

The first step is to find out if the door has a hole for a deadbolt or if it requires drilling. Mark the position of the hole for the deadbolt on the surface of the patio door lock replacement by using the template supplied with the lock installation set. Utilize your tape measure to determine the height of the deadbolt. Mark this height on the door edge. Use speedsquares to draw a straightline across the mark that you made to mark the bolt hole.

Then using a power drill, bore through the hole until it is on the opposite side of the door. It may take a while. Then, sand the hole and the edges of the door until it is smooth. It's also an excellent idea to stain or paint the door at this point.

When the door is open remove any screws that are visible on the existing deadbolt. This will reveal the back and front assemblies of the deadbolt, and also the bolt inside. Then, loosen the bolt and Replace Door Lock it with a brand new bolt that matches the door hardware. The bolt is usually attached to a set plate, which you will need to unscrew. Once this is done, you will need to chisel out the area for the strike plate on the door frame.

If your strike plate is out of alignment, it could be because the previous installer did not mortise it correctly or a weatherstripping has changed the strike's location. To fix this problem it is necessary to remortise the strike plate and the deadbolt. Close and lock the deadbolt when you've completed this step. Make sure the bolt is extending into the strike plate and then test the key to ensure it is able to open and close smoothly.

Knob

It could make your home or business less secure if the door knob is worn. It may make it more difficult to open or close the door, which is why it's a good idea to replace patio door lock it. It shouldn't take more than 30 minutes. Use a screwdriver or pliers to remove any knobs or handles. Be cautious not to scratch other parts of the door.

Before starting, you'll want to spray WD-40 or a different dry lubricant onto the mechanism of the door knob. This will allow the new lock move smoothly when you turn it. To ensure that it operates properly it is important to select a knob and handle that are compatible with your patio doors locks replacement. If you don't have a doorknob that is compatible then you'll have to purchase a replacement.

Before you begin the replacement process, examine the old knob to see what screws are holding it in place. If there aren't screws, you can use the screwdriver to secure the cover plate into the screws plate that is hidden.

After you have removed the knob take it apart and look for evidence of damage or rust. If the knob has any dents or marks it's time clean it. Otherwise it shouldn't require any major work.

It's time to install the new one. It is important to first look over the two knobs to ensure that you've chosen the right one for the door. You'll need to select one with an extending rod that is interlocked with the rod mechanism of the other knob. Once you've put the new knob into the hole, slide it into the latch.

Thread the latch plate screws downwards, then test the spring by pressing down repeatedly. The latch should spring up every time. Next, install the other new knob and connect it with the rod mechanism on the previous knob. Attach the other long screws from the interior knob through the hole in the cylinder of the doorknob outside and lock it in place.

Latch

A latch is a piece metal that extends through the door jamb to keep it closed. The latch is operated by a handle or knob on the interior of the door, or a thumb-turn on the outside. The latch can be secured by deadbolts to stop intruders from breaking in through the glass. It also offers protection from accidental or intentional closing of the door by children or pets. You can choose to install an entry point with either a single-cylinder deadbolt or double-cylinder deadbolt, depending on the level of security.

Installing a latch involves the same steps as installing a deadbolt, however, there are a few variations. First, you must measure the setback of the doorjamb by using a tape measure to be sure that the new lock will fit. The setback is measured from the edge of doorjamb all the way to the center of hole for the latch plate. The standard setback is 2 3/8 to 2 3/4 inches. If your setback is higher it is possible to purchase a latch that is longer from a hardware or locksmith store.

The next step is to drill an edge bore hole into the doorjamb for the latch plate. Use a chisel and chisel the latch mortise. Make sure the depth is sufficient for the faceplate to be in line with the doorjamb. Put the strike plate into the correct position to ensure it's in the right position.

If the strike is set too high, the door could be pushed in or pressure applied to it using a crowbar, or tire iron. This could cause the doorjamb to crack. To correct this issue, the strike can be lowered by drilling another hole in the doorjamb and chiseling out the core of the old hole.

Installing the new strike plate is the final step. This can be done by screwing the new plate over the screw holes that are already in place. Then you can use wood putty to fill in the old screw holes and the bolt hole that will not be used. Once the putty has dried then sand it to an even finish.

Strike

An electric strike is the metallic part where the deadbolt and latch are engaged when the door is closed. It is an essential component of the lock's overall security because it stops the door from opening and gives additional resistance to force or kicking. If a door has been equipped with an electric strike, it will only be opened by a key or the control unit which controls the electrical impulses.

Traditionally, installing an electric strike required cutting a small portion of the doorjamb in order to remotely remove the latchbolt of a circular lock from the pocket within the strike. This change can be an inconvenience when it comes to the appearance of an opening as well as exposing the keeper mechanism and latchbolt to unintentional users.

Recently, several electric strikes manufacturers have created a "No Cut" kind of strike that doesn't require a cutout for operation. They use a specific design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike is equipped with an internal ramp that raises the keeper and latchbolt when it receives an electrical impulse from a controller or reader. The latchbolt and replace door lock keeper are pushed higher on the ramp thanks to the retraction. When the door is closed, the deadbolt is retracted and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy task, especially when you are replacing the strike on a previous door. However, if you're upgrading to an electric strike for an access control system, you'll have to ensure that your new system is compatible with the model of lock you've chosen to install. Also, you must ensure that the strike is connected to your access-control system and is configured to operate in a fail-safe way.

One way to safeguard against access by unauthorized persons is to upgrade the strike on your doors to a robust strike plate. These plates can be fitted with up to six screws of three inches instead of the usual two screws of three-fourths inch. These longer screws make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.