• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

The first protection is your door lock. It can stop unauthorised entry to your home. Signs of wear and tear and even instances such as moving into a new residence or break-ins, can necessitate the need to replace your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to purchase the appropriate lock.

Deadbolt

If you want to ensure your door is safe from criminals, it's a great idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder to break through the door. A single cylinder deadbolt is activated using a key on the exterior side and a thumb turn part on the interior. A deadbolt will only work if it's installed correctly, though.

First, you must determine whether the door already has a hole that is suitable for a deadbolt, or if you need to drill it. Utilizing the template included with the lock installation kit mark the location of the deadbolt hole on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Then, mark the height on the edge of the door. You can then use a speed square to draw straight lines across the mark you made for the bolt hole.

Then, use a drill to drill this hole until it extends to the other side of the replacing upvc door lock mechanism. This may take some time. Sand the hole and edge of the door to make it smooth. It's also a good idea to paint or stain the door at this point.

Once the door is ready, remove any screws that are visible on the deadbolt. This will reveal the front and rear assembly of the deadbolt and its internal bolt. Then, loosen the bolt and Replace Door Lock it with a new one that matches the door hardware. The bolt is usually connected to a setplate, which you will need to unbolt. After that, you'll have to chisel the area on the upvc door locks replacement frame for the strike plate.

If your strike plate is misaligned it's likely that the previous installer didn't properly mortise it or a weatherstripping came along and changed the strike position. It is necessary to re-mortise the strikeplate and possibly even the deadbolt to correct this problem. Close and lock the deadbolt after you've completed this step. Test the deadbolt by closing it and locking it once the bolt has been extended into the strike plate.

Knob

It can make your home or business less secure if the door knob is worn. It can make it more difficult to open or close the door, which is why it's recommended to replace it. It shouldn't take you longer than 30 minutes. Use pliers or a screwdriver to remove any old knobs or handles. Be careful not to harm other parts of the door.

Spray WD-40, or replace door lock a different dry lubricant on the mechanism of your door knob before you begin. This will help the new lock to move smoothly when you turn it. It's important to use the best knob and handle that is compatible with the doors you currently have to ensure proper operation. If you don't already have a doorknob that matches, you will need to purchase a new one.

To begin the replacement process, look over the knob or handle to find what screws are holding it in place. If there are no screws then you can use the screwdriver to wedge the cover plate into the screws plate hidden behind it.

Once you've removed the knob, check it for signs of damage or rust. You'll have to scrub it off if you notice any scratches or dents however, you shouldn't need to do anything if the knob is in good working order.

Now is the time to put in the new one. Begin by examining the knobs you've chosen to make sure that you're selecting the correct one for your door. You'll want to pick one with an extending rod that is designed to lock with the rod mechanism on the second knob. Once you've put the new knob over the door's hole carefully slide it into the latch.

Test the spring by pressing it down repeatedly. The latch should pop up every time. Install the second knob, and lock it to the rod mechanism of the first knob. Then, thread the other long screws from the interior knob through the hole in the cylinder of the exterior doorknob and secure it.

Latch

A latch is a metallic piece that extends into the doorjamb to secure it closed. It is operated by a handle or knob on the interior side of the door, or a thumb turn on the exterior side of the door. A deadbolt is a device used to secure a latch and prevent intrusions from breaking through the glass of the door. It also offers protection from the accidental or deliberate closing of the door by children or pets. A latch can be set using one cylinder deadbolt or replace Door lock a double cylinder deadbolt, based on the level of security you prefer.

Installing a latch follows the same steps like installing a deadbolt but there are a few distinctions. First, determine the setback of the doorjamb by using an instrument to make sure the new lock will fit. The setback is the distance from the edge of the doorjamb, to the center of the hole to accommodate the faceplate for the latch. A standard setback is 2 3/8 to 2 3/4 inches. If you have a greater setback, you may need to purchase a longer latch from a hardware store or locksmith.

The next step is to drill an edge bore hole in the doorjamb to accommodate the latch plate. Utilize a chisel to make the mortise for the latch. Make sure that the depth is enough to allow the faceplate to be in line with the doorjamb. Put the strike plate into the correct position to ensure it is positioned correctly.

If the strike is positioned too high, the door could be pushed into or pressure put on it with a crowbar or tire iron. This can also cause the doorjamb to break. To remedy this, the strike can be lowered by drilling a new hole in the doorjamb and chiseling out the core of the previous hole.

Installing the new strike plate is the final step. This can be done by fixing the new plate to the screw holes that are already in place. Then apply wood putty to fill in the holes from the previous screws and the bolt hole that will not be used. Once the putty has dried, sand it to an even finish.

Strike

The metal piece that engages the deadbolt and latch when the door is closed is an electric strike. It is a vital part of the lock's overall security because it prevents the door from opening, and also provides an additional level of resistance to force or kicking. If a door is fitted with an electronic strike, it will be opened only with keys and the control unit that controls its electrical impulses.

In the past, installing an electronic strike required cutting off a part of a doorjamb, which would remove the latchbolt on a cylindrical lock from the pocket that is inside the strike. This modification can be an inconvenience in terms of the appearance of openings, and it also exposes the mechanism of the latchbolt and keeper to unauthorized users.

Recently, a number of electric strike makers have come up with an innovative type of electric strike called the "No Cut" strike that doesn't require a cutout in the doorjamb for operation. The strikes use a unique design to allow the latchbolt and keeper to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp that raises the latchbolt as well as the keeper when it receives an indication from an individual reader. The latchbolt and keeper are pushed higher on the ramp thanks to the retraction. When the door is shut the deadbolt remains in at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike is an easy process, particularly in the case of replacing upvc door lock mechanism the strike on a previous door. However, if you are upgrading to an electric strike for an access control system, you'll be required to ensure that the new system is compatible with the kind of lock you've installed. You will also need to ensure that the strike is properly wired to your access control system and is set up for fail-safe operation.

Upgrade your strike plates to heavy duty strike plates to stop the entry of unauthorized persons. These plates are fitted with four to six screws of three inches instead of the two, three-fourth inch screws typically employed in regular strikes. These longer screws make breaking the frame to reach the piece that turns the thumb on a single cylinder deadbolt more difficult.