• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace upvc door lock to replace door lock Door Locks

Door locks are your first protection against unauthorised access to your home. Signs of wear and tear, as well as instances like moving into a new house or burglaries, could trigger the necessity of replacing your lock.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will enable you to buy the right lock.

Deadbolt

Installing a deadbolt is a ideal way to secure your door from burglars. The bolt extends into the strike plate that is on the doorframe when it is locked, making it much more difficult for burglars to gain entry through the door. A single-cylinder deadbolt is activated by a key located on the exterior and a thumb-turn device located on the interior. Deadbolts are only effective only if it's correctly installed however.

The first step is to determine if the door already has a hole for deadbolts, or if it has to be bored. Mark the location of the hole for the deadbolt on the surface of the door by using the template supplied with the lock installation set. Use a tape measure to determine the height of the deadbolt. Then, mark the height on the edge of the door and use the speed square to draw a straight line across the mark you made for the bolt hole.

Then, use a power drill to drill this hole until it is on the other side of the door. This may take a while. Sand the hole and the door edge to smooth it. It's also recommended to stain or paint the door at this point.

When the door is open take off any screws visible on the deadbolt. This will reveal the front and back assemblies of the deadbolt, and also the bolt that is inside. Then, remove the bolt and replace it by a new one to match your door hardware. The bolt is often connected to a set plate that you need to unscrew. After this, you'll need to chisel the door frame for the strike plate.

If your strike plate is misaligned, it's likely because the previous installer didn't mortise it correctly or a weatherstripping popped up and changed the strike position. You'll need to re-mortise the strike plate and possibly even the deadbolt to correct this problem. Close and lock the deadbolt once you have completed this step. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

It can make your home and business less secure if the door knob is worn. It could make it more difficult to open or close the door, which is why it's an ideal idea to replace the knob. Replacing knobs is an simple DIY project that shouldn't take less than 30 minutes to complete. You can use a screwdriver as well as pliers to take off the old knob or handle However, be careful not to scratch any of the other components on the door.

Before you begin, you'll want to spray WD-40 or a different dry lubricant onto the mechanism of the door knob. This will help the lock to move smoothly when you turn it. To ensure proper operation it is essential to select a knob and handle that match the doors you already have. If you don't already have a doorknob that matches then you'll have to buy a replacement locking mechanism for upvc doors.

To begin the replacement process, look over the knob or handle to see what screws are holding it in place. If there aren't any screws, you can make use of a screwdriver and wedge it between the cover plate and the plate with hidden screws and remove it.

After taking the knob off examine it for signs of rust and damage. If the knob shows any dents or marks then you'll need clean it. Otherwise it shouldn't need any major work.

Now is the time to put in the new one. You must first study the two knobs to make sure that you've chosen the correct one for your door. You'll need to choose one with an extender rod that locks with the rod mechanism of the second knob. Once you've put the new knob over the hole in the door carefully slide it into the latch.

Test the spring by pressing it repeatedly. The latch should spring back up every time. Then, put in the new knob and lock it with the rod mechanism on the first knob. Then, thread the other long screws from the knob's interior through the hole for the cylinder on the exterior doorknob and lock it in place.

Latch

A latch is a steel piece that extends out into the doorjamb to secure it closed. The latch can be operated by a knob or handle on the interior of the door, or by a thumb-turn on the exterior. Deadbolts can be used to secure a latch and prevent intrusions from breaking through the glass of the door. It can also protect against accidental or intentional closing by animals or children. The latch can be fitted with one cylinder deadbolt or double cylinder deadbolts according to the security level you prefer.

Installing a deadbolt can be the same as installing a latch however, there are some distinctions. To make sure that the new lock will fit first, you must take a measurement of the setback on the doorjamb with a tape measure. The setback is measured from the edge of doorjamb up to the center of hole for the latch plate. A standard setback is 2 3/8 to 2 3/4 inches. If your setback is higher than that, you might need to purchase a latch that is larger from a locksmith or hardware store.

Then, make a hole for the latch plate into the edge of the doorjamb. Utilize a chisel to smooth out the mortise for the latch making sure it's large enough for the faceplate of the new latch to sit in a flush position with the doorjamb. Place the strike plate in place to make sure it is positioned correctly.

If the strike is too high, you could kick the door in or apply pressure using the tire iron or crowbar. This can cause the doorjamb to break. This can be corrected by drilling a new hole through the doorjamb, then cutting the core from the hole that was previously made.

The last step is to install the new strike plate which can be accomplished by screwing it over the existing screw holes. Use wood putty then to fill in any old bolt holes or screw holes that won't be used. After the putty has dried then sand it to a smooth finish for an elegant finish.

Strike

An electric strike is the metallic piece where the latch and deadbolt engage when the door is shut. It is a crucial component of the security of a lock, as it seals the door and provides extra resistance to kicking or gorillainvestment.com force applied to the door. If a door is fitted with an electronic strike, it can be opened by using keys and the control unit that regulates its electrical impulses.

In the past, putting in an electronic strike required cutting a portion of a doorjamb, which would let the latchbolt of a cylindrical lock from the pocket within the strike. This is a drawback when it comes to the appearance of an opening and also exposes the keeper mechanism and latchbolt to any unauthorised users.

Recently, several electric strikes manufacturers have come up with a "No Cut" type of strike that does not require a cutout in order to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike has an internal ramp that raises the latchbolt and keeper when it receives an electrical impulse from a reader or controller. The keeper and latchbolt are lifted higher up the ramp by the retraction. When the door is closed the deadbolt remains extended and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward procedure, particularly when you're replacing a patio door lock an older strike. If, however, you are upgrading to an electric strike for an access control system, you'll need to make sure your new system is compatible with the type of lock you have installed. Also, you must ensure that the strike is properly connected to your access control system and is set up to function in a fail-safe manner.

One way to protect against unauthorized access is to upgrade the strike on your doors to a robust strike plate. The plates are made of up to six screws of three inches instead of the usual two screws of three-fourths inches. The longer screws make it harder for anyone to break the frame and reach inside to turn the thumb turn piece of a single deadbolt cylinder.