• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is a nuisance. It could be a chance to upgrade your windows to energy efficient or insulated ones to enjoy benefits such as improved comfort, higher resale value and lower utility costs.

You can do it yourself for a fraction of what it would cost to employ an expert. You'll only require the appropriate tools and a few minutes of your time.

Glass

If your single-pane windows are old damaged, cracked or deteriorating replacing them with modern glass that is tempered or insulated can increase energy efficiency and reduce noise while preserving the historical integrity of older homes. The process of replacing a window pane is relatively easy and can be accomplished by most homeowners who possess basic hand tools. You will also require an additional window pane, glazier's tips, pliers, and latex glazing putty. If needed you may use a heatgun to warm the old putty. Before starting, wear protective gloves and goggles since working with broken glass replacement windows may cause injuries.

Begin by removing any broken pieces of glass. It is best to use pliers however, a flathead may be useful equally. Use a wood chisel, or putty knives to remove any remaining old putty around the frame and the window sash. Be careful and slow making sure not to break the existing window sash. It is recommended to work on a stable ladder rather than on the ground and to have someone standing below the sash to help hold it steady.

Prepare the window frame to accept the new pane after you have removed the old glue. Measure the width and height of the sash opening, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to a hardware or home center store to get a piece cut of stock glass to the right size. You can cut the glass yourself if you possess the right tools.

After installing the glass Apply some caulking around the edge. This will make the glass weatherproof. Then, place a glazier's tip on each side of the frame to hold the pane in its place. The points shouldn't be so tight that they cause friction between the frame and sash However, they should not be loose.

Before applying the putty, work it in a gentle manner until it is smooth and free of lumps. Then, roll it into pencil-size strips. Place the first strip in the corner of the frame, moving from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier’s points are small triangular pieces of steel that help secure the glass to the frame without causing damage to the delicate surface. It's simple to learn how to use this nefarious tool, and you'll save money on the expense of an expert installation.

After the old putty as well as the glazier's points have been removed and the frame is thoroughly cleaned with a knife to remove any remaining residue. Lightly sand the frame in the rabbet grooves to smooth out rough areas. If you sand wood, protect it with painter's tape to avoid accidental damage.

Write down the exact dimensions of the frame. These dimensions can be taken to the hardware or home center store, and the new pane will be cut a bit smaller. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Insert the new pane into the frame and push firmly using your hands. Make use of the chisel's point or the edge of the putty blade to tap the glazier's points, as shown in Figure 11. The glazier's point should be aligned with the top edge of the pane and the shoulders raised should be just beneath that lip.

Apply a thin layer of glazing compound on the rabbet grooves and edges of new glass. This will seal and protect the edges. Allow this to dry and cure completely.

Install the new window sash when the glazing compound has dried. First, saturate the wood with a thick coat of Linseed oil. This will stop the new putty from sucking up the moisture and deteriorating and cracking over time. Use a brush to apply this coat, or even the tip of the putty blade. Then use the chisel that is on the back of the putty tool or the back of the handle to gently hammer the new sash or glazier's tip into the rabbet grooves. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball thrown or a rock thrown in error or a branch falling can result in a cracked or cracked window. Most windows Replacements near me can be repaired easily by simply putting in a fresh piece. The glass is held in place by small clips made of metal called a glazier's point and putty, which is often called glazing compound. Before you install a new pane, first remove the old one and clean the area using an abrasive and an abrasive scraper that is a pull type or an abrasive wood chisel. Wear protective glasses and gloves while you do this work. You'll need a heating gun when the window handle replacement is fixed to the frame.

If you are planning to replace the original sash, remove the molding pieces that secure the old pane. Then, sand the sash to make sure it's flat and ready to be re-caulked. Once the sash is installed then, apply a new silicone caulk to the glass window replacement to ensure it will not leak or change color over time.

Remove the glazing points from the rabbets, or the grooves in the sash where the glass sits. If they're difficult to cut, place an instrument such as a heatgun over them to soften first. If you're using a heating gun, make sure not to scratch the railings or sash by holding the tool too closely.

Prepare the bed replacement handles for windows your new pane by removing the old glaze and putty. Roll a rope made of glazing compound between your fingers and then make it about 1/2 inch thick. Then, push it into the rabbets in which the glass will rest. It's important that the glass sits on the putty on both sides, so if you need to, lightly tap the glass into the rabbet using your thumb.

If the new pane has a crack, you can cover it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. If the crack is not sealed, you'll need to use putty to keep water out. Once the putty is dry clean the oily film from the glass and allow it to dry completely before painting. Paint after the putty has completely dried. It will not form a good seal and may leak or discolor with time.

Paint

You might be worried about replacing a damaged piece of glass. However, replacing one glass pane does not have to break the bank if you do it yourself. Even double-paned windows can be replaced for a fraction of what it costs for a professional.

If you're working with a large glass window first, ensure that it is securely attached to the frame. This can be done relatively easy and fast with the proper tools and techniques.

When you are ready to begin with the removal of the window pane. Take out the glazing points made of metal that are attached to it. These are basically small metal triangles that act as "nails" that hold the window in place within the frame of wood. They are submerged beneath a bead or glazing glue that hardens to a solid wedge which holds the wood frame in place and conceals the edges.

After you have removed the old pane removed Clean up the frame and wood. Scrape off any old paint and sand the rabbet grooves where the glazing points were. They should be sanded to the point of being bare, to allow you to paint them the same shade as the rest of the frame. After the sanding process, apply a coat of flax oil to the wood that is not sanded down to help extend its lifespan.

Then, take measurements of the dimensions of the window's opening. You'll need to determine the vertical and horizontal dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure that you get a precise size for the new pane. This will allow for seasonal changes in the glass. Take these dimensions to your local hardware or home improvement store and ask them to cut you cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.