• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Programming a Subaru Key Fob at Home

Depending on how much to replace a subaru key fob to program subaru key fob (have a peek here) old your Subaru is, you might need to have your key fob programmed by an auto locksmith. This is typically accomplished by connecting a programming machine to the car's computer.

To program your Subaru begin by unlocking the driver's side door using the door button control and then close it. You will hear a chime from the instrument panel, and the dome lights will flash.

Step 1: Locate the Transmitter Circuit Board

There are several ways to program your key fob. First, you must determine the type of key fob that you have. This can be done by studying the shape of the key fob or by listening to the car's sound.

Once you have the information you require, you can begin the process of programming your key fob from home. To do this, you will need a metal key and a screwdriver with a flat head. You can open the key fob by twisting. Then push the key made of metal in and release the battery from the tiny tabs that hold it in place. Replace the battery and then put the case back together.

Step 2 Step 2: Unscrew the Key Fob Case

It is a good idea to change the batteries in key fobs in case they're not working. However, there are situations where the buttons on the key fob may be damaged. If you notice the buttons' contacts made of metal have come loose Try the process of re-soldering them to get them working again.

Before you start the process, make sure the doors of your car are shut and that your ignition is turned off. You can accomplish this by closing the driver's door and pressing the door button ten times in quick succession. After that, you'll hear the instrument panel chime, and your dome lights will flash. This means you're ready proceed.

Step 3. Insert the fob of your key into the ignition

A lot of articles on the internet will explain how to program your brand new or replacement subaru key Subaru keyfob at home. However, most of them don't provide precise instructions. Programming an electronic key is best done by an expert auto dealer in Fort Bliss or a locksmith.

Sit in the driver's seat of your Subaru with the engine turned off and the doors shut. Use the door button control and use it to unlock all doors. Open and close the driver's door three times. Then, insert and remove the key from the ignition switch (don't turn it) 10 times within 40 seconds. The system should chirp to confirm that the settings have been altered.

Step 4: Turn on the ignition

Before you begin this process of programming a key fob, it is important to remember that this method only works with a functioning key already. If you don't an auto-locksmith or a dealer will need to program keys for your Subaru Fort Bliss.

Once the key is programmed, it will be capable of starting your car within five minutes. Start by closing the doors and then shutting off the engine. Sit in the driver's seat and unlock the doors by pressing the button for the door. Place the key into the ignition then turn it on to the off position (the electrical systems will turn on but the engine remains off), and then back to the off position 10 times in rapid succession.

Step 5: Unlock the Driver's Door

Subaru offers a wide range of high-end cars with key fobs that lock and unlock the doors and even start the car and defrost the windows. These devices are sometimes not working.

To resolve this issue, you should contact a locksmith or the dealer. This will solve the issue and ensure your vehicle is secure.

To do this, open the driver's door, then close it. Place the key in the ignition and then turn it to position 1. Then, you can turn it back to the off position. Do this as quickly as you can ten times. After ten times, you should hear a chime.

Step 6 6. Press the Lock/Unlock Buttom on the Driver's Door

The process of replacing a subaru key the battery inside the subaru new key fob cost remote key fob is easy. The fob's case on the outside is opened. Make use of a flathead to pry the interior case open and then remove the batteries that were in there.

After taking the battery out then replace it with a new one. Close the case. Assume a seat in the driver's chair and unlock all doors using the door button control. Place the key in ignition and turn the key so that the electric system is on, but the engine remains off. Repeat this 10 times in a line until you hear a chime sound on the instrument panel. This will put the system into programming mode.

Step 7: Press on the Passenger Door Lock/Unlock button

The irritating chirp that can be heard when unlocking or locking the Subaru Key Fob from the outside of the vehicle can be distracting for some owners. In some cases the chirp can be removed by opening and closing the doors as well as a double-click of the lock button on the key fob.

Switch the ignition off and close all doors, as well as the lid that holds the fuel. Press and hold the lock side of the key fob's lock button for 10 seconds. After that the instrument panel will emit an audible chime. The chime signals that the lid for the fuel-filler and door are locked. It is possible to change the setting to make doors lock automatically without the need to press a switch.

Step 8 Step 8: Enter the 8-Digit Transmitter Number.

Write down the first series of 8 digits and keep it in your wallet. Then, sit in the driver's chair, close the doors and turn the key into the first position. After 10 turns, your instrument panel should sound at least once.

The circuit board that controls the transmitter is within the key fob case. There should be one or two sets of numbers (8-digits) on the circuit board. Follow the instructions in the guide to register the code. For older models, this procedure might require a visit to the dealer.