• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet to come and go as they please without having to let him in or out. They also help keep your cat from having to go to the bathroom in the house.

It is much easier to put the cat flap on a upvc panel than one made of glass but you'll require some expertise and appropriate tools.

Take a measurement of the door

Installing a cat door into a front door could be difficult however, as long as the cat flap is of the appropriate one and you follow the guidelines, it shouldn't be too difficult. We will help you draw the shape and then use the jigsaw to cut the door area. Then we'll complete the job by affixing the flap. This will ensure that the flap stays in place and protects the door from rain and wind which can cause damage.

To determine the size of the cat flap that you need, measure the width of your pet. This will ensure that the flap is large enough to let your pet leave and enter the home without having to open and Fitting cat flap in upvc door panel close the door every time, but it is also small enough to keep them from going too far either way.

Once you have the measurements you can mark out the location on the door where the template should be placed, usually, this is done using an X, however some kits include an illustration that outlines the location to drill, if yours does, then you can stick it to the door and draw a line around it. If your door has a moulding or sill on the bottom edge of it ensure that you have enough clearance from these to keep your cat safe and will prevent them from getting access to your home.

Then put on your eye protection and a dust mask and using a jigsaw, begin to cut according to the lines you penciled in, don't try to push the blade too hard because this will make it cut faster than you would like it to. If you have an already-cut square, make use of it to verify that you are cutting correctly and to ensure that the hole is a proper rectangle. Once you are happy with this you can start to remove the remaining door material.

Draw a Line

The cat flap is a great method to let your pet out and in without worrying about them coming in with guests or leaving unwelcome gifts in the house. It also helps prevent draughts and keeps your home's temperature steady. The installation of a fitting cat flap in upvc door panel flap your door might seem difficult for those who haven't attempted it before. Many people call an expert carpenter or joiner to complete the job. While this is certainly an option, it's possible to do the work yourself if you have the proper tools and follow instructions with care.

While this is much simpler when using a timber door it is still feasible in uPVC doors - although you must be careful not to scratch the doors, as this can cause damage to your warranty. The first step is to measure the door and ensure that it will fit the new cat flap. This isn't too difficult when you have an ordinary uPVC door, however you may need to take more care if using an insulated or composite type of door as these are more difficult to cut into than solid uPVC panels.

The next step is to determine the size of your cat's belly. This is the amount of height between the floor and the underside of your cat's stomach. You'll need to locate a space at the entrance that will allow your pet to pass through comfortably. Once you know this, you will need to mark out the area using a pencil and a spirit level so that you can ensure that the hole you will create will fit your cat.

After you have marked the area, it's time to cut out the hole. It is crucial to be patient and use a jigsaw ensure the cuts are clean and smooth, not rough and uneven. This could damage your door. Wear safety glasses and a dust mask when working with a Jigsaw. Inhaling sawdust is hazardous for your health. After you have finished cutting the hole, you'll require sandpaper for smoothing the edges so that the cat flap can be easily fitted into place.

Cut a hole

Getting a cat flap fitted into an existing door panel or double glazing sealed unit can be quite difficult. If you're not experienced in DIY, it's recommended to hire a professional to complete the job for you. A botched job could not only look ugly but also pose a security threat. It could allow cold air in when the cat is outside and hot air out when inside.

The first thing you have to do is draw the location of the hole in the door with an eraser and a spirit level. This will ensure that it is properly located and is flush with all the other parts of the door. Make sure you have a piece of sandpaper at the ready to smooth any edges.

Once the line has been traced, you must cut the hole using the jigsaw. Remember to wear the appropriate safety gear for working with an electric tool. If you're worried about the noise, you can buy a cordless jigsaw which is more quiet and easy to use.

It is important that you only cut away the material that is required to fit the cat flap. A small amount of material will be needed to cover the thickness of the the cat flap itself but cutting off more than this can cause problems or cause damage to the door frame.

If the door is made of upvc and has a metal panel or frame, it may interfere with the microchip flap. In this case you'll need to create an extra-large hole to ensure that the metal does not touch the walls of the flap.

If you're planning to install the cat flap installer flap onto an upvc door or a double-glazed window with a metal frame then you will need to speak to a specialist who can supply you with a new glass pane that already has the hole for the cat flap premade in it. This is less expensive than trying to fit a cat flap inside an existing pane that was not made for this purpose.

Fit the Flap

Cat flaps give your pet the freedom to come and go whenever they want, allowing them to relax in the home whenever they'd like. If you have a uPVC front door, it can be difficult to put in the cat flap. This is especially true in the event that you don't own a glass panel that is cut. If you're looking to install a half-glazed uPVC replacement panel, it is possible to install a cat flap. It's not a simple matter of drilling an opening in the door. It is also necessary to take a few steps to ensure that it is secure.

A uPVC, GRP or composite door panel usually has a flimsy plastic outer skin joined to a soft polystyrene insulating core. It is crucial to be cautious when cutting the material. This type of door usually comes with a template drawing which you can use as a reference to cut the hole in your door.

After you have carved out the hole in your front door, it's time to install the cat flap. You can purchase and install a wide variety of different models that range from simple push-button operated ones to microchip-activated ones that allow only your pet. Whatever type of cat flaps you choose it's essential that your cat can utilize the flap with ease without getting stuck outside in the rain.

A circular fitting a cat flap in a upvc door cat flap in upvc door panel (click the next document) is more effective than a square one, as circles can be cut more securely into the glass. This is because square holes are more likely to crack the glass when they're drilled. It's also a much safer choice to use since you're not at risk of drilling into toughened glass that could shatter and cause injury to your pet or family members. This is particularly important if you have child or an elderly person living at home who could be injured by shards glass.