• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Properly Start a Wood Burning Stove

Wood stoves are a warm method to heat a room and also save energy. However, they need some level of maintenance.

Many modern wood stoves comply with EPA emission guidelines. You can check for an EPA sticker on the grate or under it to make sure your stove isn't releasing harmful pollutants.

How to Start a Wood Fire

The scent and sound of a wood fire can be a pleasant addition to any home. However, it is important to know the correct method to build a fire in your stove. Incorrect methods can result in a fire that doesn't burn effectively and can cause smoke or creosote. The tips below will assist you in starting a fire that will heat your home with minimum effort and with the highest safety.

Before you start a fire, check the condition of your logs and coals. If they're too damp they could smother the fire and prevent it from burning properly. You might also want to open the flue to let any ash out that has been deposited into the stove.

Begin by placing a handful of small dry pieces of newspaper into your stove. This will help to ignite the tinder and kindling. Once the tinder and kindling have started to burn, you can add an additional layer of larger pieces on top. This should be done with a crosshatch design so that there is air between each piece.

If you own a wood stove with an automatic control of combustion, it will automatically feed an air stream controlled to the fire as it grows. This will allow the fire to burn at a steady rate without the need to open the stove's doors to keep it in check.

It is essential to avoid using excessive tinder as this could result in the fire burning at an extremely high rate and fails to use the fuel as efficiently as possible. Once you've made a solid base in your stove with tinder, kindling and embers to start the main flame, you can do this by laying two large logs of the base on the grill. Then, on the top of these base woods, place a layer perpendicularly to them. This method of building the fire is known as a "top-down" fire will result in an effective and long-lasting fire that will not engulf the larger base logs.

Once your fire is well established Close the damper and keep it closed. The fire may be smothered by opening the damper prior to it being fully established. It will also reduce the efficiency of the fire.

Adding Wood

Stoves can be used to heat your home efficiently and save you money. They can be used in conjunction with a central heating system or furnace to provide additional heating for large houses. A lot of the stoves that are clean-burning employ a superior combustion process that differentiates the burning of volatile compounds from combustible gasses and tar by supplying air in two different stages. The first stage allows for the vaporization of the volatile compounds, while the second step offers fresh air that is pre-heated. This improves the process of combustion and helps to reduce the smell.

The amount of heat you can get from your stove will depend on the kind of wood and the moisture content and the size of the logs. The logs should be stacked in a well-ventilated area for several months prior to when you try to burn them to give the wood time to dry. If the logs are too wet they will create a lot of steam that is basically wasted energy.

You should add wood to the pile at intervals, not all at all at. In addition, adding too much wood at once could cause the temperature to rise within the firebox, creating a vortex which pulls smoke and volatile compounds that are not burned back into flames. This can reduce the effectiveness of your stove.

It is recommended to stay clear of other combustibles such as paper or cardboard in your stove, since they are not wood stove burning and have very different physical properties that cannot be burned without creating dangerously high temperatures and a lot of emissions. Also, you should not use compressed combustibles like wood briquettes because they have a distinct chemical and physical composition to real firewood and aren't type-approved for burning in wood-burning stoves.

If you're installing a wood burning Stove wood burning in your home, it is crucial to have it installed and tested by a qualified. A certified WETT technician can test your installation to ensure that it is safe and efficient. They will also check that your chimney works correctly. They also provide maintenance services to keep your chimney and stove in tip-top shape. They can inspect the accessible areas of your chimney for leaks, and repair any problems found. They will also ensure that the residents of the house are aware of and adhere to the fire evacuation procedures in case in the event of an emergency.

Adjusting the Damper

A damper regulates the amount of heat that is lost up the chimney when you aren't cooking on your stove. Additionally, it can also help you to control the flame. If the flue is not open but the damper is closed too much the fire will not burn as efficiently and will release smoke into your living space. You can adjust your damper to ensure the best flames by experimenting with different positions.

You want to keep your damper open to allow air to be able to enter and exit the flue when a flame is burning. This will allow the fire to start and stay lit for many hours. A proper opening will keep the fire from being starved of air, and also prevent it from blowing out smoke.

To adjust your damper correctly first, make sure that the fireplace has been preheated and that the wood stove is hot. This will ensure that the chimney stays warm and has a good draft. Once this is accomplished the damper for the wood stove can be adjusted.

After the fire has been burning for a while, you should close the damper about three quarters of the way. This will stop warm air in the room from venting up the chimney while still allowing the smoke to escape out of the wood stove.

This is the best way to prevent the fire from getting too hot, while also keeping it burning. If you shut the damper too much, it could stop the draft from working, however when it's too wide, a cold breeze could blow through your home.

You can determine how much the damper is opened by holding your hand near the top of the of the flue pipe. If you can feel a slight breeze pressing against your hand, it is probably in the open position.

The damper settings may differ from one stove to the next and even among different types of wood. You can experiment garden shed with wood burner various settings to get a sense of the ideal setting for your stove.

Clean up

After a fire, it is essential to clean the stove and flue. This can reduce the chance of an ensuing fire in the chimney, which is the primary reason for fires caused by wood stoves. Creosote, a sticky material that can accumulate inside the stovepipe, is very dangerous. It is caused by moisture and unburned wood particles that are unable to escape the fire. It can also be caused by poorly lit fires.

A regular cleaning routine helps to prevent the buildup of creosote. This can be accomplished by sweeping your chimney once a year. It is also recommended to get your stove and fireplace professionally cleaned and checked at least year.

It is also a good idea to clean out the ash tray and grate regularly. It is a good idea to use only wood that is seasoned for burning, as it will create less creosote as well as ash. Avoid burning paper, cardboard and plastic. These materials can release harmful chemicals to the air and flue, that could end up in your home.

The glass in the wood burning stove has to be regularly cleaned too. Many newer wood stoves are designed with self-cleaning glass, which means they do not require much scrubs. You can apply stove glass cleaners to the window if you're capable of getting the glass as clean as you'd like on your wood stove.

Other suggestions to maintain your wood stove include lowering the vent when you're not using it, and slamming doors or windows to increase airflow. This keeps the fire burning more hot and efficiently. The cheapest wood burning stoves stove will not need to be as active to circulate air. It is a good idea not to stack logs or place them on the fire for an extended period of time. This can cause warping and splits. It is advised to avoid using compressed combustible wood burners in your wood stove since the paraffin in the logs can melt and leak into the flue which could cause damage.