• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Saab 9-3 Key

The Saab 9-3 is a car that has a large amount of appeal for drivers. It has good visibility and an impressive performance engine. It also has a high safety rating.

However, it is important to ensure that you have two keys working for your car. It could be costly to replace a key if you lose it.

How to Replace the Ignition Key in the Saab9-3

You must replace the car key in the event that it isn't turning. This guide will explain how to replace the ignition key on the Saab 9-3. You will need to replace the key, buy an updated reprogrammable phone, and buy a new case for your key-fob.

In contrast to older models, the majority of modern Saab vehicles use a transponder on the key-fob instead of a physical key to unlock and start the car. The rechargeable batteries contained in the key-fob expire, and they aren't able to hold any charge. This is especially when you keep using the same key with the same lock.

The good news is that the battery can be replaced easily by a professional locksmith. If you have the right tools, and a little patience, you can do it yourself. The first step is to take the key-fob out. This is accomplished by inserting a flathead screwdriver in the slot that is located in the middle of the case. You will need to work slowly, since the plastic is extremely thin and is susceptible to damage.

When the case is opened and the case is opened, you can make the new key by combining the lower half of the key that was used previously with the banana and transponder on the new key. This will ensure that the new key is connected to the CIM properly, which can make a big difference when replacing the only key for your saab replacement key 9-3.

How to Replace the Ignition Key in a Saab 900

Unless you have two keys, you'll have to take off the steering wheel and dashboard in order to access the ignition. Start by disconnecting the negative battery cable. After the battery has been disconnected, you can remove all the trim pieces as well as dashboard pieces that surround the steering wheel. Once the dash has been removed, you can put screws into the hole behind the ignition switch.

The ignition cylinder is fitted with a key lock that could prevent the vehicle from starting if you don't have a key. If your 900's ignition switch isn't working, look at the key to see if it's in the lock or in the ignition barrel. It is also important to rotate your keys and keep them clean to avoid being bent.

Saab cars differ from other cars because they do not use traditional metal keys. Instead, the car detects electronic signals coming from the key fob by using the use of a special microchip.

If you lose your sole working key fob, the dealer will charge you top dollar for replacing the computer module (known as the CIM). But we can reprogram your existing computer EEPROM and prepare it to accept new keys without replacing it. This will save you up to 50% of what the dealer charges! We call it the SAAB KEY PROGRAM. Find out more here!

how to open a saab 93 without a key to Replace the Ignition Key on a Replacement saab 9-3 key 9-5

The metal component of a traditional saab 9-3 key fob programming key is easy to copy, and is also not a major obstacle against vehicle theft. The electronic part of the key-fob has a chip that recognizes the car when the key is put in the ignition switch.

saab key code's anti-theft system has relied upon this technology for over 10 years. It's not quite as effective as a door lock however it makes stealing your car more difficult. This is the reason why every Saab owner should keep an extra key available.

Most new Saabs come with two keys in the factory. However, you can add more at a dealer through a special handheld computer, called a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 cars, with more modern, newer features that require an ignition key.

The dealer will replace the CIM or TWICE module in these cars if all keys are lost, and they'll charge you top dollar for doing it. We can however reprogram the EEPROM in your existing computer and prepare it to accept new keys without replacing the expensive modules.

How to Replace the Ignition Key in a Saab XC90

If your SAAB 9-3 key fob begins having trouble turning the lock barrel It could be the time to replace it. It's a simple process and you don't have to visit a dealer. You can do it at home, using a couple of basic tools.

First, you'll need to prepare the keys for your new car. Before you begin, disable the anti-theft feature by placing blocks underneath the rear wheels and activating your handbrake. Insert the key in the ignition and turn it to the "on" position. This will activate the accessories, but it will not start the engine. Repeat this process 5 times, and then leave the key on the "on" position.

You'll need to purchase an additional case for your key fob. They can be found at a variety of auto parts stores and are generally inexpensive. Based on the model, you can even get them without any electronic components.

To open up the case, place a flathead screwdriver inside the slot that is in the middle and gently work it. The case will break easily, and once you've done that, you'll have access to the internal electronics. To take the electronics out, make use of a small screwdriver and try prying them out in a gentle manner.